Solar for Wire, Cable and Wiring Device Makers in New Jersey
Wire, cable and wiring device makers in New Jersey run drawing machines, extruders and molding presses through long shifts, and a rooftop array can evaluate that electrical load.
LandAir supports commercial solar planning, engineering and project coordination for New Jersey properties. The review starts with the building, its electric accounts and the owner's goals.
Review your actual bills, property constraints and design assumptions.
Review the property
Review electric use
Define the project
Solar for cable manufacturers drawing, extruding and cabling
Cable plants run long, continuous lines. Rod breakdown and fine drawing machines pull copper or aluminum through dies, annealers soften it, and stranding and cabling machines twist conductors together. Extruders with heated barrels coat the conductor in insulation and jacket compounds, then cooling troughs and take-up reels finish the run. Fiber optic cable adds draw towers and ribbon lines. Wiring device makers mold housings, stamp contacts and assemble switches and receptacles on powered lines. Many of these lines run through several shifts, so a daytime array covers part of a round-the-clock load. Extrusion heaters, drives and chillers all draw power throughout the weekday. Potential New Jersey production incentives depend on the current program, project category, registration and eligibility. Confirm the applicable terms before modeling revenue.
- Site-specific energy cost modeling
- Review of ownership and operating costs
- Project eligibility review
- Property and tenant planning
Solar planning for long lines, reel yards and process cooling
Cable buildings are long and low, with machines laid out in straight runs from raw rod to finished reel. That shape gives a roof large, regular sections for panels, and our Professional Engineers review framing before any design is final. Process cooling towers, chillers and exhaust from extrusion lines sit on or near the roof, so we set clearances around them. Reels of finished cable wait in outdoor yards, and a ground mount or carport canopy there adds capacity. Wiring device plants have injection molding presses and stamping lines with their own motors, which we include in the load study. We prepare township permits, coordinate interconnection with the utility, and arrange conventional commercial bank financing so your company owns the system.
Related: Electrical and Transportation Equipment Manufacturers and Commercial solar cost guide. See every business type we cover on our industries page.
- Electric bill review and usage pattern check
- Roof and site constraint review including access and safety
- Preliminary layout and sizing assumptions you can validate
- Early notes on permitting and interconnection requirements
- Clear next steps for design, pricing, and timelines
Review project economics and eligibility
Compare installed cost, financing, expected production, utility charges and ongoing operating obligations for the specific property. A production estimate is separate from a savings estimate; demand and fixed charges may remain.
Federal tax treatment and New Jersey production incentives have separate eligibility, ownership, registration and timing rules. Confirm the applicable requirements with the program administrator and your tax advisor before including benefits in a budget. See the New Jersey commercial solar incentives guide and cost and ROI guide.
Confirm each assumption before including it in a project budget.
Project cost
Review the complete scope, exclusions and financing terms.
Tax treatment
Eligibility and the benefit your organization can use require tax-advisor review.
Program eligibility
Confirm current program rules, registration and project requirements.
Production and usage
Model expected output separately from savings using the actual utility tariff.
Plan the project sequence
Share bill and site details
Develop the design and approvals plan
Agree construction and handover
What's Included for Wire, Cable and Wiring Device Manufacturers
Rod breakdown and wire drawing
Drawing machines run large motors and coolant pumps to reduce rod to wire. They operate across shifts, and daytime hours supply the share of their load that an array can offset.
Annealing and stranding
Annealers and stranding machines add heating and motor drive load along each line. Our load study reads your bills for the baseline these lines set across the weekday, then sizes the array against it.
Insulation and jacket extrusion
Extruder barrels hold heat for long runs while screw drives and puller motors turn. Heating elements make extrusion one of the larger electric loads on a cable floor, and part of it falls in daylight.
Cooling troughs and chillers
Water cooling after extrusion relies on pumps, chillers and cooling towers. Their demand follows summer heat, which is also when solar output is highest, but cooling demand and solar output do not necessarily peak together; compare the actual interval profiles.
Fiber optic draw and ribbon lines
Fiber makers run draw furnaces, coating curing lamps and cabling machines in conditioned space. These loads add to weekday demand and fit well beneath a rooftop array that produces through the same hours.
Device molding and assembly
Injection molding presses, contact stamping and automated assembly make switches and receptacles. Heater bands, hydraulics and conveyors all draw power during the working shifts that a rooftop array also serves.
Property considerations
Roof and structure
Operating patterns
Maintenance
Meters and ownership
Approvals and access
Critical operations
New Jersey project support
LandAir supports commercial solar project planning across New Jersey from Cherry Hill.
Discuss your commercial solar project
Share the property address, electric usage and the decision you need to make. Review feasible options and the next steps with LandAir.
Frequently asked questions
Our extrusion lines run through the night. Does solar still help?
Yes. The array covers a portion of the load during daylight hours, and SuSI income follows every megawatt hour produced, regardless of when your lines run. For an eligible account, excess generation may earn bill credits under the utility's applicable tariff and settlement rules. Credits do not necessarily offset fixed or demand charges.
Is a long, low building good for solar?
Often it is. Long, regular roof sections give panels clean rows with few obstructions. Our engineers confirm the structure, set clearances around cooling equipment and exhaust, and check wind and snow loads for your region.
Could we use the reel yard for solar?
Possibly. Potential New Jersey production incentives depend on the current program, project category, registration and eligibility. Confirm the applicable terms before modeling revenue. Township review applies, and we prepare that submission for the property along with the engineering package.
Who handles utility interconnection?
LandAir prepares and submits it with your utility, whether PSE&G, JCP&L, Atlantic City Electric or Rockland Electric. Our engineers review your service with your electrician, so the system connects at the right point.
